Frequency ranges |
N 470 to 700 MHz |
Switchable channels |
40 groups of 60 channels fully user programmable |
Switching-window |
Up to 232 MHz |
Frequencies |
Microprocessor controlled frequency synthesizer circuit, with 25 kHz minimum step. The frequencies are easily PC reprogrammable with the optional UPK Mini Programming Kit |
Frequency error |
< ± 2.5 ppm, in the rated temperature range |
Temperature range |
-10 to +55 °C |
Modulation |
FM, with 50 μs de-emphasis |
Nominal deviation |
±40 kHz (Max. operating dev. = ± 60 kHz) |
Antenna input impedance |
50 ohm SMA type (SWR < 1:2; typ. 1:1.4) |
Sensitivity |
-
- 2 μV ( 0 dBμV), for SND/N > 58 dB
- 5 μV (14 dBμV), for SND/N > 98 dB
in the whole switching window
|
Amplitude response |
< 0.5 dB (RF input sig.:6 dBμV to 100 dBμV) |
Co-channel rejection |
> 2.5 dB |
Adjacent chan. selectivity |
> 80 dB typical (for ch. spacing ≥ 400 kHz) |
Spurious rec. rejection |
> 100 dB |
IF image rejection |
> 90 dB |
Intermod. rejection |
> 76 dB |
IIP3 |
> +10 dBm typical |
Spurious emissions |
< 2 nW (typical = 0.1 pW) |
Noise Reduction system |
ENR (Wisycom Extended-NR), noise optimized
ENC (Wisycom Extended-NC), voice optimized & with reduced pre-emphasis
Others, compatible with most systems, through an internal DSP emulation of SA572, SA575 and Rms envelope compander chip set, fully user programmable |
AF bandwidth |
30 Hz to 20 kHz |
Frequency response |
± 0.5 dB in the 30 Hz to 19 kHz range |
Distortion |
0.3 % typical |
SND/D ratio (Analogue) |
110 dB typical [*] |
SND/D ratio (AES3) |
>125 dB typical [*] |
POWER LEDs |
2 multicolor RGB LEDs to easy indicate Rx1 & Rx2 power status:
- GREEN, if “Receiver ON” with external power supply
- RED, if LEDs blinking indicates power supply status of transmitter
- slow blinking, at 25% battery capacity
- fast blinking, at 12.5% battery capacity
|
RF LEDs |
2 multicolor RGB LEDs to easy indicate Rx1 & Rx2 RF status
- RED, if both receivers RF level is under squelch level
- GREEN, if signal above squelch level & antenna A (green) is active
- BLUE, if signal above squelch level & antenna B (blue) is active
- YELLOW, if signal above squelch and both antenna are used
|
AUDIO LEDs |
2 multicolor RGB LEDs to easy indicates Rx1 & Rx2 audio status
- RED, if audio is muted because of squelch (or tone squelch if active)
- GREEN, if audio is active and tone squelch present
- BLUE, if audio is active and tone squelch not present
|
Front buttons |
Simple operation with 4 buttons to quickly monitor and setup the receiver
One touch function for frequency scan and sync function |
Powering |
- External = 5 to 18 Vdc (1.5 W max)
- Autonomous. = with optional BCA 42 Battery Module (5 x IEC-LR6 1.5V size-AA alkaline or rechargeable batteries)
|
Dimensions |
“Slot-in” end plate = 68 x 18 x 115 mm, “Stand-alone” end plate. = 68 x 18 x 135 mm |
Weight |
180g approx |
Analogue Audio Output |
- Audio line-output electronically balanced on two 3 pin mini-XLR Female connector
- Audio line-output level Adjustable in one dB steps between -20 and +6 dBu (nominal) and MAX +12 dBu (peak deviation)
- Audio line-output imped. ≤ 200 ohm
|
Push to Talk (PTT) Audio Output |
electronically balanced on a 5 pin mini-XLR Male connector |
Digital Audio Output |
- electronically balanced on 3 pin mini-XLR Male connector
- AES3 @ 48 kHz
|